975 REVERSIBLE PLOW
Reversible Plow
- Moldboard frame pivots with the bottoms
- Safety-trip standards available to save time
- Plastic moldboard and steel shins
- Rear gauge wheel
View Product Brochure
Features
975 mainframeAll 975 Moldboard Plows use only one set of bottoms.
The moldboards are reversed laterally by a hydraulic cylinder that is standard equipment. There are several advantages of this design over traditional two-way rollover plows with two sets of bottoms:
- Requires less 3-point hitch capacity
- Requires less ballasting of the tractor front end
- Eliminates initial cost and service requirements for one complete set of standards and bottoms
Reversing pin
The reversing pin is positioned at a 13.5-degree angle, instead of being straight up, for even plowing in both directions. The reversing pin does not require adjustments by the operator.
The V-style mainframe is made of 152-mm x 102-mm (6-in. x 4-in.) welded tubular steel to handle the stress of tough plowing and reversing action as well as tight turns:
- 5-mm (3/16-in.) thick on three-bottom plows
- 8-mm (5/16-in.) thick on four- and five-bottom plows
Integral in-furrow hitch Compatible with tractors equipped with Quik-Coupler, the integral hitch offers unexcelled maneuverability in turns and when parking in tight areas:
- Tractor rockshaft lever controls the raising and lowering of the plow
- Maximum plowing depth is 356 mm (14 in.)
Adjustable width of cutThe width of cut on all 975 Moldboard Plows can be set at 406 mm or 457 mm (16 in. or 18 in.) by moving the standards to different bolt holes in order to:
- Match the tractor horsepower to the soil conditions
- Improve the residue-handling ability
- Improve productivity
- Maximize fuel efficiency
The underframe clearance is 813 mm (32 in.) to allow excellent material flow through the plow.
975 Moldboard Plow rear gauge wheelAll 975 Moldboard Plows come with a rear gauge wheel included in standard equipment. The rear gauge wheel provides the following features:
- Controls the plowing depth of the rear of the plow in rolling terrain
- Stabilizes rear of the plow in soft soils
- Adjustable through a full range of plowing depths
- Designed for easy turnbuckle adjustment
- Equipped with 6.70-15 tire to eliminate bulldozing in soft soils
Specifications
Compare the specifications of up to 4 models
| Key Specs | 975-reversible-plow Current Model |
|---|---|
| Total width of cut | |
| Option 1 | 0.63 to 0.91 m 2.67 to 3 ft |
| Option 2 | 1.2 to 1.4 m 4 to 4.42 ft |
| Option 3 | 1.6 to 1.8 m 5.25 to 6 ft |
| Option 4 | 2.0 to 2.3 m 6.5 to 7.42 ft |
| Plowing depth | 35.6 cm 14 in. |
| Horsepower required - Option 1 | 2-bottom: 37.3-52.2 kW 50-70 hp |
| Option 2 | 3-bottom: 52.2-70.8 kW 70-95 hp |
| Option 3 | 4-bottom: 70.8-104.4 kW 95-140 hp |
| Option 4 | 5-bottom: 96.9-123 kW 130-165 hp |
| Hitch | |
| Type | Category 3N, 3, or 2 |
| Steering | Integral, in-furrow Yes Integral, on-land No Semi-integral, on-land No Drawn, in-furrow No Drawn, on-land No Quick-coupler compatible Yes |
| Reversible | Type of reversing Hydraulic cylinder Yes |
| No. of bottoms | |
| Option 1 | 2 |
| Option 2 | 3 |
| Option 3 | 4 |
| Option 4 | 5 |
| Option 5 | |
| Option 6 | |
| Option 7 | |
| Option 8 | |
| Total width of cut | |
| Adjustment | Manual |
| Option 1 | 0.63 to 0.91 m 2.67 to 3 ft |
| Option 2 | 1.2 to 1.4 m 4 to 4.42 ft |
| Option 3 | 1.6 to 1.8 m 5.25 to 6 ft |
| Option 4 | 2.0 to 2.3 m 6.5 to 7.42 ft |
| Option 5 | |
| Option 6 | |
| Option 7 | |
| Option 8 | |
| Weight (approximate) | |
| Option 1 | 408 kg 900 lb |
| Option 2 | 544 kg 1,200 lb |
| Option 3 | 771 kg 1,700 lb |
| Option 4 | 1,043 kg 2,300 lb |
| Option 5 | |
| Option 6 | |
| Option 7 | |
| Option 8 | |
| Clearances | |
| Vertical | 81.3 cm 32 in. |
| Fore-aft | |
| Standards | |
| Shearbolt | Standard |
| Safety trip | Optional |
| Spring reset | No |
| Hydraulic | No |
| Coulters | |
| Option 1 | |
| Option 2 | |
| Option 3 | |
| Bottoms | |
| Option 1 | Plowing depth 35.6 cm 14 in. Steel moldboard |
| Option 2 | Plastic moldboard |
| Option 3 | |
| Option 4 | |
| Option 5 | |
| Option 6 | |
| Frame | |
| Option 1 | Thickness for 2- or 3-bottom: 15.2x10.2x0.478 cm 6x4x0.188 in. |
| Option 2 | Thickness for 4- or 5-bottom: 15.2x10.2x0.64 cm 6x4x0.25 in. |
| Option 3 | |
| Expandable | |
| Horsepower required | |
| Option 1 | 2-bottom: 37.3-52.2 kW 50-70 hp |
| Option 2 | 3-bottom: 52.2-70.8 kW 70-95 hp |
| Option 3 | 4-bottom: 70.8-104.4 kW 95-140 hp |
| Option 4 | 5-bottom: 96.9-123 kW 130-165 hp |
| Landing | |
| Gauge wheel | |
| Tires | |
| Trashboards | |
| Additional features | |
Accessories and Attachments
Bottoms
Steel shinsSteel shins are available as a field-installed option only.
The frog is pre-drilled at the factory to accept this attachment.
With this attachment, the steel shins will allow longer wear life when soil first comes into contact with the plow, but still offers the option of a plastic moldboard for sticky soil conditions.
Hydraulic Cylinder
Wheels and Tires
Rear gauge wheelA rear gauge wheel can be ordered for plows not so equipped.
Rear gauge wheels:
- Control the plowing depth of the rear of the plow in rolling terrain
- Stabilize the rear of the plow in soft soils
- Provide easier turnbuckle adjustment
- Are adjustable through a full range of plowing depths
- Come with 6.70-15 tire to eliminate bulldozing in soft soils